MOSAIC-X5 INDUSTRIAL RECEIVER WITH ETHERNET AND POE

Industrial IP67 all-constellation multi-frequency top-performance high-precision RTK GNSS receiver based on the mosaic-X5 engine, with Ethernet and PoE.

Built for permanent outdoor duty. IP69K-rated housing has exactly one opening: a sealed 12-pin industrial connector carrying power, Ethernet, RS-232 and USB through a single mating cable — nothing to gland, nothing to seal on site, nothing to corrode. RS-232 rather than bare UART lets the receiver talk directly to industrial controllers, marine electronics and existing vehicle systems over long cable runs, with no level converter in a junction box. In the field it runs on PoE or on a wide 9–36 V input that takes 12 V and 24 V vehicle, machinery and marine supplies directly; on the bench, 5 V over the same connector's USB line powers and configures it with no external supply at all. Operating from −10 °C to +60 °C and rated for high-pressure washdown, it mounts straight onto a mast, a roof, an implement frame or a wheelhouse — at a price normally reserved for enclosure-less boards and indoor-grade units.

Custom cable on request at info@gnss.store

Housed in a sealed IP67 enclosure with an industrial 12-pin connector, this receiver takes Septentrio's mosaic-X5 engine and packages it as a fully assembled, field-ready unit — connected over a single cable and built to keep delivering centimeter-level RTK where bare OEM boards can't.

The mosaic-X5 engine tracks all Global Navigation Satellite System (GNSS) constellations and supports all current and future signals, and brings Septentrio's suite of signal-protection technologies:

IONO+ — advanced protection against ionospheric disturbances. Ionospheric activity degrades GNSS signals, ranging from loss of RTK fix to total loss of signal lock; IONO+ was honed by Septentrio supporting applications in the most iono-active regions on Earth to deliver the most advanced ionospheric protection of any receiver.

AIM+ — Advanced Interference Monitoring and Mitigation provides built-in protection against intentional and unintentional jamming and spoofing through a sophisticated system of signal sampling and mitigation. In robotic platforms, neighboring electronics can emit RF radiation that interferes with GNSS signals; AIM+ counters such interference, resulting in faster set-up times and robust, continuous operation.

RAIM+ — Advanced Receiver Autonomous Integrity Monitoring applies fault-detection across every level of the receiver, from measurement generation through quality control and navigation algorithms. Faulty measurements — typically caused by high multipath or an active ionosphere — are detected and removed from the solution.

In robotic devices neighboring electronics can produce RF radiation which interferes with GNSS signals. AIM+ offers protection against such interference resulting in faster set-up time and robust continuous operation.

Advanced Receiver Autonomous Integrity Monitoring (RAIM+) comprises fault detection mechanisms of the receiver at all the levels including the generation of measurements, quality control and navigation algorithms. Detected faulty measurements, which are typically caused by high multipath or active ionosphere, are removed from the solution.

• Outside Industrial IP67 device
• Industrial 12 pin connector
• Connection options: connector, engineering kit, or installation cable
  
• Custom cable is available on request
  
• Powered by PoE, 9-36V, USB or 5V
• Passive PoE is IEEE 802.3af-2003 compatible
• Ethernet with Power over Ethernet support
• Antenna inputs with SMA connectors
• PPS output on SMA connector
• USB
• RS-232
• 32GB SD card inside for data logging
• PPS output
• Breakout box with interface connectors for RJ-45, 2 x USB-C, USB-A, DC-10LP, and DB-9
• Purple Power LED, Green Ethernet LINK, Red PVT LED (GPLED), Orange RTK LED (GPLED2). GPLED/GPLED2 functions are configured in the receiver
• RxTools Control and Analysis Software
• Extensive visualization and evaluation features
• Dimensions: 133.0 × 118.8 × 36.0 mm
  
• Weight: 250 g
• Work temperature: -40 °C ~ +60 °C
• Mounting method: screw mounting
• Fully assembled, tested and ready to use

Kit content:

• mosaic-H INDUSTRIAL dual-channel receiver.
• USB-C cable, 3 m (included only with the “USB cable” variant).
• Connector with 50 mm flying leads (included only with the “Connector” variant).
• Engineering kit, comprising a 1 m cable and a breakout box (included only with the “Engineering kit” variant).
• Installation cable, 10 m, terminated with RJ45, DB9, and a DC connection (included only with the “Installation cable” variant).
  
• Custom cable available upon request. Please contact us at info@gnss.store for further details.